Welcome to Jiujiang fire fighting equipment Co., Ltd
ADD：No.1,Daqiao Road,Yujiahe,Lianxi District,Jiujiang City,Jiangxi province,China
Jiujiang fire fighting equipment Co., Ltd © CopyRights
Jiujiang fire fighting equipment Co., Ltd
Fire-fighting protective clothing ZFZH-JXA
(1). the outer layer using M52608C Bangwei Puthida dual silk den fabric, mass per unit area (220 ± 11) g/m2;
Flame retardancy: Longitudinal flame propagation time 0s, loss length 17mm, latitudinal afterflame time 0s,
Breaking strength: warp 1787N, latitude 1614N;
Tear strength: longitude 647.4N, latitude 478.2N;
Humidity resistance: ≥3 grades;
Thermal stability: change rate 2%;
Color fastness: 4 washable stains, 4 water-resistant friction;
(2). Waterproof breathable layer (insulation layer) using DYZ14-2 aramid non-woven fabric + flame retardant PTFE
film fabric, mass per unit area (125 ± 6.25) g/m2;
Flame retardant: Longitudinal burn time 0s, loss length 37mm, latitudinal afterburn time 0s, loss length 30mm;
Hydrostatic pressure resistance: >50kPa;
Moisture permeability: ≥5000g/(m2.24h);
Oil Repellent Performance: ≥3;
Thermal stability: change rate 2%;
(3). The comfortable layer is made of Bangweiptai thermopoka fabric of M51210, and the mass per unit area is
Flame retardancy: Longitudinal burn time 0s, loss length 25mm, latitudinal afterflaming time 0s, loss length 27mm;
Breaking strength: longitude 545.7N, latitude 479.2N;
Thermal stability: change rate 1%;
(4). reflective tape with 3M reflective tape;
Flame-retardant properties: Longitudinal burn time 0s, loss length 20mm
Latitude continuous burning time 0s, loss length 18mm;
(5). Overall thermal protection performance: 31.5cal/cm2;
(6). Seam breaking strength: the (weft) to ≥ 650N;
Applicable to body protection, the firefighter command suit is a windbreaker design with three layers of outer
layer, waterproof and breathable layer (heat insulation layer), and comfort layer. It has the advantages of flame
retardant, heat insulation, waterproof and breathable, antistatic, etc.
At the bust, hem, and cuffs of the command suit, a 360° reflective strip with a width of no less than 50mm is
stitched to identify.
(1). the clothing should be cleaned immediately after wearing.
(2). washing should be as much as possible to wash the surface layer. It can be washed with neutral detergent,
then dry and then cool after washing: if drying, the temperature should not exceed 60 ℃ when drying, in order
to prevent the air permeation layer from blocking the micropores and affect the air permeability effect.
(3). It is forbidden to repair the garment privately. If damaged, it must be returned to the factory for repair.
(4). clothing should be stored in a ventilated and dry room, avoid prolonged exposure to the sun, avoid storing
with dangerous chemicals, and store the whole box on a board or shelf to prevent dampness.
(1). guard against paralysis psychology, because firefighters protective clothing has the good heat insulation
performance, the firefighter may reduce the sensitivity to the heat wave after wearing, easy to produce the
paralytic psychology. Please be careful not to lower your vulnerability to fire when working. Do not expose your
body, and fire fighters may be burned unwittingly.
(2). in the presence of chemical dangerous goods, chemical gas, radioactive hazards and other environments
prohibited to use alone, should wear appropriate protective equipment.
(3). No contact with high-temperature objects or metals to avoid injury to operators after clothing damage.
(4). Water gun and spray protection must be used in the working environment when close to the flame and in high